Finally, steam into the jacket should shut off, the unloading door is to be opened
Subsequently the shaft and mixing arms are reversed to act as unloading mechanism and ought to scoop the waste fragments out of
the unloading door, onto a conveyor belt or directly into a waste container.
The boat should now be ready for a different cure cycle, using retained the majority of its heat for the treatment of the
following batch.
(B)Features and Specification of the Steam Boiler:
Characteristics of the Boiler:
It must be an Electrical boiler
Splash proof electric enclosure and switches
Door Isolator to main electric enclosure
Alarm lights and Safety/protection against excel pressure
Level control on feedback water tank
Technical specification of the Boiler:
Output: between: 90-110 kg/h (F&A 100 deg C)
Working pressure: between 7-10 pub
Boiler water content: between 80-100 liter
potable water tank content: between 60-80 liter
Power consumption: between 60-75 Kw
quantity of Heating Elements: 3-4 nos.
Electrical requirements: 400Vac, 50 Hz, 3 ph
(C)Technical Specifications of Tub washer
Characteristics:
Fully automatic and manual modes.
metallic construction, SA 240/304
Sensors to maximize both system performance and operator safety.
Must use Re-circulating cold wash water to minimize water consumption and operating expenses
Disinfects all bin surfaces
Uses Powerful blow dryer to remove excess surface water
Must be compliant with all North American and EU regulations
Specifications:
Tub washer capable to wash bins of a suitable size, the standard being 38 gram
Must get an water reservoir of ability minimal: 225 liter
Perfectly suited for hospitals and clinics by processing around min.300 bins each hour.
Time to dry and wash one bin following loading-approximately 12 nos.
Bins loading on wash channel at a time -approximately 12 nos.
Total length: approx 30.0 feet
Total length: approx 8.0 feet
Total length: approx 3.0-3.5 feet
Height to Conveyer from floor: approx 3 feet.
Drive of the Tub washer
Motor driven
Motor Horsepower: approx. 4.0 HP
Power: 220vac, 1 ph or 400 VAC, 3 ph or to suit customer wants
Bins to be included
200 nos.
Gearbox: ought to be Parallel shaft
Shock Protection: Rubber Mount Torque Arm
Power: 220vac, 1 ph or 400 VAC, Ph or to suit customer wants
Ancillaries to be included
Shredder stand, manufactured out of 3″ sq. steel tube, standard height 30 inches
Shredder hopper, fabricated from 16 gauge steel, with optional switched hopper lid
(E)Features & Technical Specification of Conveyer
To carry processed waste from boat to shredder
Controls
Motor starter with overload protection
Control housing Nema Sort 12
security pull-stops along either side of conveyer
Ancillaries
Conveyer stand, manufactured out of 2″ sq. steel tube
Raised sidewalls fabricated from 16 gauge steel
Dimensions
Over-all span: between 20-25 feet or appropriate length based on the setup requirement.
Over-all width: between 24-30 inch
Over-all height (without including stand): between 12-14 inch
Available slopes: 0-40 degrees
Belt speed: 75 ft/min
Dam spacing: approx. 16 inch
Drive
Motor driven
Horsepower:approx. 0.75 HP
Motor RPM: approx. 60
Electric Power input: 220vac, 1phj or 400 VAC, 3 Ph or to match customer wants
(F)Technical Specification of Tipper
Characteristics:
It’s to be made to permit for easy bin placement under the doorway to unload processed waste and easy
maneuverability for lifting and tilting the waste into the shredder hopper.
Equipped with 2 binds to adapt processed waste heaps to be loaded into the shredder and shredder waste to be
transported to the disposal bin.
Frame: Rugged heavy duty frame constructed of formed and welded steel for extra strength
Mast: Fabricated using cannel steel for increased strength and dependability. Open structure layout complete with security
cage to offer increased visibility.
Over-all length: between 20-25 feet or appropriate length depending on the installation requirement.
Over-all width: between 24-30 inch
Over-all height (without including stand): between 12-14 inch
Available inclines: 0-40 degrees
Belt Speed: 75 ft/min
Dam spacing: approx. 16 inch
Drive
Motor driven
Horsepower :approx. 0.75 HP
Motor RPM: approx. 60
Electrical Power input : 220vac, 1phj or 400 VAC , 3 Ph or to suit customer needs
(F)Technical Specification of Tipper
Features:
It is to be designed to allow for easy bin positioning under the door to unload processed waste and easy
maneuverability for lifting and tipping the waste into the shredder hopper.
Equipped with 2 binds to accommodate processed waste loads to be loaded into the shredder and shredder waste to be
transported to the disposal bin.
Frame: Rugged heavy duty frame constructed of formed and welded steel for extra strength
Mast: Fabricated with cannel steel for greater strength and dependability. Open structure design complete with safety
cage to offer greater visibility.