Can this incinerator handle all typed of medical waste eg. Anatomical, sharps and general? Do you have spec or results with regard to Hydrogen Chloride, Hydrogen Fluoride and Sulfur Dioxide emissions. Hoe many chambers? Temperatures in the different chambers? What is the total weight excluding the chimney stack? How long time from order to delivery? My application requires 150kg/hr Price? – Waste from industrial sludge: 5 tons per month (from primary treatment plant Wastewater Treatment Cosmetic Industry 30% ST). – Common Waste (not reusable): 20 tons per month (average) – Hazardous waste: 1.8 Ton every 4 months. (average) -Incinerator Diesel Fuel -Capacity per bath 50-100Kg -time for burnout(hours)2-4 -operating temperature 950-1300 -Easy to installation -Low energy consumption levels -pathological waste and infections and contaminated surgical dressing, and plastic devices If I have are 80 beds (internal) and 270 people between outpatients and employees. Under these conditions well consider downloading this I propose 100 kgs / hour (TS – 100PLC)or would be less?Stainless steel, Destruction rate of 15kg per hour, Batch load of 10-15kg of waste and average temperature of 850 OC.Avail us a quotation for 9 units of incinerators that are stainless steel with destruction rate of 15kg per hr. bactch load of 10-15kg of waste and average temperature of 8500 degress c.
Incineration System for Medical Waste (Capacity 6 Tons Per day); Incineration System for Medical Waste (Capacity 12 Tons Per day); Polluted air control technology i.e. ( Wet scrubber, bags); Flue gas treatment system (gas emission technology). What is the Gases Emission Standard you are using? What is the fuel you are using/recommending in your equipment? medical hospital incinerator Capacity: 30 Kg. destruction capacity: 3.000 kcal/kg diesel. max consume: 2.5 gal per hour. 1 camera: 1 burner capacity: 80.00 kcal Type: K (Ni-CrNi) enter size: 500x500mm ash door: 190 x 250mm 2 camera: 1 burner capacity: 80.000 kcal. Air conbustion: 0.5 HP Type: K (Ni-CrNi) Temperature 1 camera: Normal work temperature: 750 -900? C, Max temperature: 1000? C. 2 camera: Normal work temperature: 950-1000? C. Max temperature: 1100? C. Chimey: minimum 3 meters Controlator ciclo control 110-120 v / 60 Hz.
Version , the entire carcass of animals ( cattle , horses , Sheep, pigs , etc.) , as well as biologically hazardous waste Products in the fuel stove . ? Opening Doors – the closure and fixation automated system , Which are managed remotely by the operator . ? designed to work in long mode and fast Action ( Quick Start EP – i) Fully mobile – mounted on wheeled chassis Even during the operation . Incinerators must be provided As standard equipment a special truck air retention for at least 2 seconds at a temperature of less than 850C, the combustion In order to achieve the proper effect. must be a two-chamber incinerators, primary and secondary Fuel stoves The waste products to reduce the initial volume Possible to minimize (approximately 5% sterile ash Form). Incinerators should be provided in the fuel tank (diesel ) The minimum capacity of the animal carcass incinerator The destruction of 1000 kg / hour. Incinerator capacity is calculated 8MJ/kg- material and 60 % humidity. It must be possible to use the incinerator +40 C to – 15 0C Temperature and 5% – 95% – of moisture conditions. ? PLC controller and a built-in temperature panelita complete Automatic control, a control computer, which is stored Information on the variation of temperature with respect to time and Graphic images. must have fuel with automatic control and malfunction Detection system. ?the ability to pre- warm-up , body waste burning on and off Consistency is independent of the first and secondary chambers. ensuring the incinerator with electricity , it Must be installed on the generator. clean the incinerator should be simple tools , Without using any additional equipment Incinerator to burn 25 to 30 kg/hr of waste Double Chamber Low maintenance with diesel filled and no more than 15amp 220 C 250 V KW must be stated. Onboard or inbuilt fuel storage tank, no more than 12L of diesel/hr Simple start for less operator training skills System to accommodate low power and frequent supply problems
“PYROLYTIC” combustion, by controlling the gasification of waste The incinerator manufacturer must avoid the release of black smoke and fine dust, during the loadings. It shall be able to reduce the volume of wastes by 98%. It shall be able to hold emission in the second burn with gas residence of not less than 2 […]
The incinerator plant shall incorporate a control panel for its operation. On the control panel we shall have a visual display of the chamber temperatures. This visual display must control and monitor the incinerator and his performance. Capacity of destruction in weight shall be 60 Kg/h. It should be able to operate not less than […]